Small scale full figure gymanst in water based ceramic clay

 In order to help the clay firm up and dry out a bit - plus to make it easier for the sculpt to hold its own weight, I cut her up to hollow out more. Although I did use a small bit of newspaper to bulk out her core, I find that in sculpting and moving the position around, there areas can build up thick in some areas. Surprisingly, this one was pretty symmetrical.


I removed some more of the clay from the core and the pelvis region. Once the clay firmed up

more, I was able to reattach her and continue sculpting.

Today she was strong enough to remove from the prongs that had been supporting the weight and stand on her own. I am working on finalizing her now.

Small scale full figure gymanst in water based clay

Time to start a new sculpt. This one will be a gymnast. It's currently measuring close to 9" tall is being sculpted using ceramic paperclay (CT3).

I started this same sculpt a couple of days ago using Chestnut - a highly grogged terracotta clay. The first attempt sagged so much that she kept having the weight press down on her legs and squash them. The clay is stiff and I had trouble getting it to twist when I wanted to move her pose a bit.

So after a day of modeling, carving, adding and fighting with it, I smashed it up and returned it to the bag for use in another project another day. Then I immediately started her all over again in the ceramic paperclay. This is much lighter and holds its shape on such a small scale, so I'm glad that I scrapped the first. I got twice as far in half the time on the second attempt.

The sculpt has an 'exterior armature', profiled in Bruno Lucchesi's books. The Chestnut clay was heavy and kept pulling out of the two prongs that are holding her weight. The papercaly is holding up better, but it may still need an internal rod added to her leg from under the base after firing to support the weight - time will tell. This sculpt has tiny fingers, so I'm hoping that it holds up well to sculpting and firing because in dance any gymnastics, the finger attitude means so much.

You can also see the hollowing that is going on. I rough in the shapes and then as the piece starts to dry and firm up, I can cut of the rough arms and head and hollow out and reattach. I've already hollowed her head and put it back on. The one arm is in place, the other is still off and drying a bit to be more firm.

The legs are still clunky because I really need to mass there to support in the early stages. Then I'll start to refine and take the forms down.

Figure Sculpting Demo - young dancer in ceramic clay #8

After letting the sculpt sit overnight I came back to it with fresh eyes. Something had been bothering me and I finally came to the conclusion that the dress wasn't quite right. So I spent some time adding clay and changing the way that the fabric moved. That seemed to make a pleasing difference:

Figure Sculpting Demo - young dancer in ceramic clay #7

 Making progress on the sculpt and generally pleased with her. There are some areas that need a bit more refining. The lighting is rather harsh because I just grabbed some quick pix in the studio. .

When she's fully completed I will set up the photo lights and get better photos,

I really enjoyed sculpting her and have titled this piece:

"Her  first dress rehearsal"

This was my first sculpture of a child and I have to agree with other people - kids are challenging. I did not work from a model which can add to the challenge of a piece as I try to imagine limbs in the round. The thing with children is their softness. It makes it hard to find the forms sometimes.

 This was so enjoyable that I'm certain that I'll be doing more dancers and hopefully gymnasts too.

 I have hollowed out the second arm and attached it back onto her body. Then I fleshed her out a bit more and started to define her ears.

She needs to rest a bit and firm up more. Next I'll block in the hair mass and dress before heading back to start any refining.

It was quite fun to chop off her arms and move them around. I probably took them off and on about 5 times until I had both working in the direction that I was looking for. Really looking forward to the rest.

One thing I will say about paper clay is that it re-wets readily - sometimes a bit too easily and can become water-logged...but with a little time and the proper amount of circulation, you can get the firmness of the clay back to a workable consistency.

Arm placement and hand position make a difference

 I've re-attached one of the hollowed out arms. The hand is roughed into place. The new placement of the arm is more graceful and in tune with the attitude of the sculpt.

The whole body must be in agreement, or the figure will simply look wrong or awkward - so I often revise as I'm working and will change the placement of the body in order to better tell the story, emotion or intent.

 

What to do when you drop your head?

Start over, of course! Yep, after I reattached her head, I bumped the sculpture stand and tipped the figure precariously. Consequently her head dropped to the floor with a big plop! Naturally it did a real face-plant so there was no real salvaging her. Quite gruesome, actually ;-)

Oh well, I enjoyed sculpting her and felt she was a bit stilted in expression anyway.

So I sat down today and created a new head. I also worked on her arms by cutting them off and hollowing them out. Then I started to rough in her hands. I've decided to change the position of the arms a bit, making her a bit more expressive, too. Have I mentioned how much I love the second chances you get with clay?

Happily, the new head is in place, the body has firmed up better to support the weight and I have one arm and hand attached again. The battery on my camera needs charging so I don't have enough juice to get more photos in today....I'll photo and post the progress soon....in the mean time, I'm happy with the progress of the head and face and feel that the second sculpt is better than the first.

I'm planning on having this sculpt more 'painterly' in the finish so this will be a new challenge on to over-work the surface.

Stay tuned!

Figure Sculpting Demo - young dancer in ceramic clay #6

 Off with her head!

Yes, it does seem a bit brutal. However, there are several reasons to to mutilate your sculpture. In this case I wanted to hollow the head and neck more and I wanted to work on the face "off sculpt". 

By removing the head, I have easier access to the skull and the features ~ sometimes sculpting on the full form can be awkward and space limited, so by removing a piece from the overall sculpture, you can get to it easier.

I will sculpt more on the head and re-attach later. Ears and hair are sculpted later, since they would be squashed in handling anyway.
 

Figure Sculpting Demo - young dancer in ceramic clay #5

 No time to work on Monday and only an hour this morning...so not much change, but refined the form and the arms a bit. Later today I hope to have enough time to start her hands.

Then I may remover her head to make it easier to sculpt, be sure of my wall thickness and reattach - we'll see how far I can get....

Figure Sculpting Demo - young dancer in ceramic clay #4

Last post today. Would have preferred to go further, but hubby just got home and the last of my Studio Tour visitors recently left so will call it a night!

Having people come to the studio and sculpting in front of people was a fun experience! Though I didn't get as much sculpting in, as I stopped often to talk with people and show them around, I feel like I've got a good start to this sculpt. I'll let her firm up overnight and get back to work tomorrow. Plan on trying to have her done by the end of the week so check back to see her progress....

Thanks for visiting everyone - I had a great time at the tour and plan on doing it again next year. I think I'll book a model and try to compete a figure pose over the two days next year....

Figure Sculpting Demo - young dancer in ceramic clay #3

 Here is the progress - her arms have been attached. The clay is still quite wet. I would be further along, but as it's a studio tour, I stop working to meet with visitors to explain my work and methods ; -).

There is still 3 more hours of the tour, so I will continue to work and post photos the rest of the day - come on out to visit until 5pm today~

Figure Sculpting Demo - young dancer in ceramic clay #2

Here is the progress - I've continued to move the sticks around at the form takes shape. The clay continues to sag and slump and I am continually bringing it back up to it's original height.

Next I will begin forming the arms and putting into place.

Stop by today to see the progress in person - I'll be sculpting until 5pm today as part of the Fort Collins Studio Tour!

900 Marble Drive.

Figure Sculpting Demo - young dancer in ceramic clay

For the Fort Collins Studio Tour I'm doing a sculpting demo. I'll be sculpting a young dancer with an attitude using ceramic Paper Clay. Here I've just started. The armature is a steel pipe attached to a board. I've put newspaper around the steel post and wrapped that with a slab of clay. The stick are temporary supports - the clay is wet and heavy and slumps while at this stage. It will be a couple of hours before it's stiff enough to support the weight and the sticks will come out. Will be updating the sculpt all day as I progress.

Come on out toe 900 Marble Drive in Fort Collins today from 10am to 5pm to see the progress!

Fort Collins Studio Tour Today!

It's a beautiful day for the tour. Finishing up a few details before the 10 a.m. opening!

Ceramic Paperclay Fox Sculpture

You may remember that I sculpted a small fox in oil-based clay. I'm still working on the wax pour of it for bronze. I decided that I wanted to make a larger version of this fox and sculpt it using a water-based clay for firing. Since Mile-Hi was out of the CT3 clay that I had planned on using, I opted to try this in water-based ceramic paperclay instead. I didn't do any measuring - I just dove into sculpting. While I did use crumpled paper for filling out the body, there was some distortion and I felt that there was too little clay in some areas and too much clay in others. So I cut this into pieces, hollowed out and reassemble before I completed the sculpting.

I was pleased to find that A) it was as much fun to sculpt the fox the second time around and B) I had no trouble enlarging the sculpture while keeping the same look and feel using a different medium. So, now it's drying in preparation for firing later.

Ceramic Sculpture turban wrapped woman

Finished sculpting "Hint of a Smile" today. This is water-based clay called Chestnut that I purchased from Mile-Hi Ceramics. It's rather groggy but that can be interesting. This one dried a little faster than I would have liked, due to my deadlines for illustrating my book - so there are a few cracks in the turban. However, that too, may end up being a desirable thing - won't know for sure until it's fired.

I will consider using some epoxy to put in the suggestion of a pupil highlight after firing also.

With the eyes hollowed out, there is additional venting for the sculpt. I'm hoping that offsets how thick the turban ended up. I did cut her in half and hollow her out but added the turban later so that part is fairly thick.
This sculpt is just under life size. I'll post again with her after firing.

First wax pouring of miniature fox sculpture

This is my first time pouring wax in preparation for the lost wax bronze process. I have an old crockpot that I'm using to heat the wax. This wax is something I bought an embarrassingly long time ago and can't remember what kind it is. Karen, at Sculpture Depot, assured me that pretty much any wax will work and different kinds can be intermixed. I thought I'd be really smart and put the block of wax in an old metal can inside the cooker to keep the cooker from getting wax all over it. Nice idea, but it dripped and got wax it it anyway ;-)
I'm using the pour mold (commonly called a dump mold) that I made of my miniature fox (you can see on earlier posts). After melting the wax, I took a small cup, dipped it into the melted wax and poured into the mold. Then swirled the mold around and emptied the wax back into the pot. A layer of wax remained inside. I did this several times to build up layers.
1) crockpot with melted wax in can
2) wax in the mold (I tried tape to secure the mold but it didn't stick very well - rubber bands worked better)
3) the wax mold of the fox - it has flaws and the base would need to be trimmed.
4) I was anxious to see the wax and demolded too soon - the wax was still quite warm and broke.You can see how the swirling of the wax creates a hollow casting.
5) I figured it would take several tries to learn the process enough to get good results. Luckily I can simply melt down the rejects to reuse the wax.
6) Back into the pot for remelting. I tried again that night - but the wax wasn't hot enough so it was a tad lumpy. The results were another imperfect casting so will try again later.

New terracotta clay bust in progress

 I have been swamped with designing the layout and illustrations for my newest book for Operation Outreach USA. Love illustrating for them, but wishing there were more hours in the day. Also got word that my other book, Nana's Silly Goats has been printed and is currently being shipped to the states. Nancy said it's gorgeous and I must say the color proofs we reviewed earlier looked great so I'm really looking forward to seeing them. I'll be posting some of the art on my website soon.

Currently I'm working on a new bust of an African American woman. This is sculpted in Chestnut. It's clay left over from my class with Andi Mascarenas and so was a bit stiff to work with as it's rather old. But I couldn't stand to waste the clay, so while it was quite hard, I soaked it well and let it marinate for a couple of days, then wedged it a bit to work the hard bits into the mushy bits.

This was actually started nearly 8 weeks ago and shelved when deadlines hit. When I got back to her, it had gone well past the leather hard stage, so was a challenge to get working again. I had a heck of a time cutting her in half to hollow out! Once I finally got her hollowed and put back together, I worked in her shoulders and started her scarf. These are some early photos and I should have newer ones up in the next day or two showing the progress.

Still not sure what I think of Chestnut. It's a rather stiff and very coarse clay. You can really see the grit and grog. Sometimes I like the earthiness of if it, but other times I find it distracting. I'll probably compare it with some other clays after firing. The plus-sized woman that I sculpted earlier using his clay fired nicely. It comes out a very, very dark brown color, which is interesting.

I've been accpeted into the 2011 Loveland Invitational Sculpture Show!

It's been a niggling dream for nearly all the 20 years that it's been operating. I remember seeing the articles about it in Southwest Art magazine way back when as I was living and struggling as a young artist if Florida. I always hoped to participate in this show but didn't believe in myself enough.

Thanks to the encouragement of my family and friends, I've started to apply myself to my sculpture last year. It was a real challenge to get my application and images submitted and I truly was uploading it at the midnight deadline ;-)

I am very excited about the opportunity and intend to continue to work hard, learn more and create the best I can!

Mad dash to enter the Loveland Sculpture Invitational Show

It's been a busy month! After finishing my latest children's book, Nana's Silly Goats,  and signing a contract for another one with Operation Outreach USA, I worked long hours getting my submission ready for the 2011 Loveland Sculpture Invitational. I had to purchase some lights and backgrounds and practice my photography, as I couldn't afford to go with a professional photographer at this time.

Having no other place, I set up a temporary photo studio in the garage (thank goodness we insulated!) and learned to control my white balance and lighting better. It took two trips to Boulder (pretty drive, but still a 2+ hour round trip) to Mike's Camera to get the softbox and paper.

Next I scoured off the patinas that I did in class that I felt were too dark and heavy. Since I didn't like the existing patina, I figured it wouldn't ruin it to try and take it off and do another. So I spend days doing glazes on the ceramic until I found what I liked. This seated woman, "Sitting Pretty" is definitely better with the new patina as the older one was very heavy and nearly black, obliterating detail.

The sleeping woman came out rather well - the patina is soft and warm and compliments the sleeping figure well.

Ascension is still a work in progress, but is coming along.

Next is Sweetness, my plus-sized figure and last is Contemplate, a seated nude.

Hopefully I made the deadline - it was midnight tonight, but I did have some trouble using Zapplication and by the time Paypal processed it was 12:01.

Well - I did the best I could and I'm glad that I tried. Whether I made it into the show or not
learned a lot and it's all part of the journey.


Now for a well-earned glass of wine!