Tuesday, December 30, 2014

Forton Bas Reliefs can take the weather changes outside...

Colorado is an area with some extreme weather and temperature changes. Last week we had temps near 70 degrees, almost record-setting for mid to late December.

Today's high, however, was 5 degrees and I write this it is currently minus 7 degrees and will be minus 11 degrees later this evening.
I snapped a quick photo of my cast bas reliefs in the snow today. I had to brush them off as they had been covered with more than 8" of snow earlier.

The wild temperature and humidity changes haven't affected them at all and they look just as lovely on the garden walls in the snow as they do with summer blooms around them.

It's nice to have outdoor sculptures that hang on garden walls, courtyards and fences to enjoy all year round.

Monday, December 22, 2014

Making a rubber mold for high bas relief tutorial

The sculpture is complete and ready for the mold. I am using Polytek's Poly 74-20 to make the mold. The sculpture is a high relief measuring 18"x 24" x 3" and took nearly all of the small 6lb kit of rubber. Since this is a fairly large and high relief I opted not to do a poured block mold. The block mold would have been easier and faster to make would would wasted a lot of mold rubber. A blanket mold would have worked too but I opted for a brush-on mold with a mother-mold shell instead.
This kit contains one container of A and two containers of B. You must stir B very well prior to mixing and directions state that use of a gram scale is recommended. You can get away with volume measurements if very precise but weight measuring is more reliable. In my case, I didn't have a gram scale so I used a postal meter scale which is good enough.
Be I measured the weight of the empty cup and deducted it from the weights of the rubber when measuring.
Here is a breakdown of steps by photos. Note that I have a few larger detail photos at the bottom:
A) Cover your work area. This is messy and does have an odor. I set things up on a covered table and assembled necessary items - the sculpt is under plastic.
B) Spray two light coats of Release Agent over the sculpt and the support board.
C) Set up supplies: scale, rubber, plastic cups, chip brushe, stirring sticks - newspaper to catch drips.
D) Stir part B well.
E) I marked two cups with A and B and resued them when measuring out the two ingredients.
F) Weighing out Part A
G) Weighing out Part B - I was sure to wipe any drips off scale.
H) Pour 1 part A and 2 parts B into larger cup
I) With clean stick mix and stir mixture well.
J) Using disposable chip brush, begin brushing light print coat onto the sculpture. I will be working in sections - mixing new batches as I go. Brush carefully and try not to make any air bubbles. This is a very thin mixture that isn't prone to bubbling, making a good print coat to catch all the details. Don't worry that it is thin and running off the high points - you will ad more later. Most important is a thin layer all over.
K) Continue mixing up more rubber and cover entire sculpt including a minimum 2" flange around the sculpture on the board.
L) Once the first coat of rubber is on, test with your gloved finger to see when it is ready for the next coat. If the rubber stick to your glove and pulls up it not ready and you would ruin the print coat if you tried to apply more rubber - wait a bit more and test again - the rubber should be tacky and leave a light imprint but should NOT pull up with your glove (detailed photos at bottom)
M) Continue to meaure out 1 Part A to 2 Parts B and mixing in a fresh larger container with a fresh stick and apply additional coats of rubber to the sculpt. The tendency will be for the rubber to slip off high points and pool in lower areas so the low areas will build up quickly. Contentrate on the high areas now.
N) As this rubber is meant more for poured bock molds, it stays quite thin. You can thicken the mixure using cabosil or short stuff. This rubber can be poured as supplied or thickened with Poly Fiber II or Fumed Silica for brushing.
N) I had short stuff on hand so this is what I used.
O) I pour small amounts of short stuff into my mixed rubber and stir well. I'm looking to make a stiffer consistency to build up the higher areas and begin to fill in any undercuts.
P) The mold rubber needs to build up to 1/4" to 3/8" to be sturdy enough for repeated use.
Q) I continue make the each batch of rubber thicker with more short stuff and use a mixing stick instead of brush to build up and fill in all undercuts.

R) I fill a plastic key molding tray with additional rubber and let it set up. With another coat of rubber, I demold the keys from the try and imbed them in fresh rubber on the flange to help key the rubber mold into the mother mold later.
S) From set up to final coat of rubber is about 6 hours with curing between coats. I've used about 12 stirring sticks, 10 disposable brushes, and 12-15 cups. I used 90% of the rubber in the kit. After letting the rubber cure overnight I come back and cut the excess off the flange.
T) Peeling back the rubber allows me to check that it is releasing well and that the print coat picked up all the detail.
The mold is complete but I must leave it intact with the clay sculpture still inside becuase I will now need to make a rigid mother mold to nestle the rubber into. The rubber is floppy and pliable - you need a firm shell to hold the shape when casting. The reason that I needed to build up those undercuts is so that the mold will pull out of the rigid shell.
Next up will be the Mother Mold tutorial.


Friday, December 12, 2014

Sculpting the bas relief demostration tutorial part 8 - finishing the work

A bout with the flu and two small portrait commissions have kept me away from this sculpt. Now I'm feeling better and the sculptures have been shipped to Australia and it's back to work.

This relief had some drying and cracking in areas that I had to cut away and put fresh clay into. Always a risk with water-based clay when you leave a project to rest for a while. So after repairing some areas I went back into refine the flowers and then soften with a bit of water. After that, I decided to add some additional hair to the right side of her face to improve the overall composition of this piece.

While that was setting up a bit, I went into the dress to add some detail - first a hint of bodice then texture and some pleating. Finally a small bow for interest.

With some additional touchups and work in the new hair area, I finally finished up the sculpture. I would prefer to mold it right away but my schedule doesn't have the time required for multiple coats of mold rubber and this is a process that simply can't be interrupted. So it looks like I will have to spray this up well, lay it flat with several layers of plastic to try to keep it from drying too much and wait for Monday to give the mold-making process my full and undivided attention.

My next tutorial will be the process of making the mold and mother-mold for this sculpture.